Skip to main content

Recently Updated Pages

How To Change The Update Frequency Of Sensors

General Setup

    1. Navigate to the ESPHome addon    2. Select the Edit button under the desired device    ...

Updated 7 hours ago by Trevor

How To Change The Update Frequency Of Sensors

MSR-1 Setup

How To Change The Update Frequency Of Sensors

Updated 2 days ago by justin@apolloautomation.cloud

How To Change The Update Frequency Of Sensors

AIR-1 Setup

How To Change The Update Frequency Of Sensors

Updated 2 days ago by justin@apolloautomation.cloud

Putting The AIR-1 In Boot Mode

AIR-1 Troubleshooting

This will cover how to put the AIR-1 into boot mode. This is sometimes needed for uploading new f...

Updated 2 days ago by justin@apolloautomation.cloud

Putting The MSR-1 In Boot Mode

MSR-1 Troubleshooting

This will cover how to put the MSR-1 into boot mode. This is sometimes needed for uploading new f...

Updated 2 days ago by justin@apolloautomation.cloud

Updating Firmware

General Calibrating And Updating

Updating Through ESPHome Addon In HomeAssistant open the ESPHome addon Make sure you are runn...

Updated 2 days ago by justin@apolloautomation.cloud

BeardedTinker YouTube Video review - MSR-1

MSR-1 MSR-1 Reviews

BeardedTinker YouTube Video review - MSR-1

Updated 2 days ago by justin@apolloautomation.cloud

Sensor Definitions

MSR-1 Setup

Once added to Home Assistant you can configure different settings for your sensor. Below is what ...

Updated 1 week ago by Trevor

General Tips

MSR-1 Setup

MSR-1 (Picture from Smart Home Scene) Light Sensor (LTR-390UV) When mounting the MSR-1 b...

Updated 1 week ago by justin@apolloautomation.cloud

Adding The MiCS-4514 Gas Sensor To The AIR-1

AIR-1 Setup

1. Unplug your AIR-1 from power and follow the video

Updated 1 week ago by justin@apolloautomation.cloud

Adding The SCD40 CO2 Sensor To The AIR-1

AIR-1 Setup

1. Unplug your AIR-1 from power and remove the back 2. At the bottom center there is a black c...

Updated 1 week ago by justin@apolloautomation.cloud

Adding CO2 To MSR-1

MSR-1 Additional Info

1. Unplug your MSR-1 from power and remove the back 2. Remove the board from the case and orie...

Updated 1 week ago by justin@apolloautomation.cloud

Make It Work Tech YouTube Video Review - MSR-1

MSR-1 MSR-1 Reviews

Apollo MSR-1 Review starts at 31:22.

Updated 1 week ago by justin@apolloautomation.cloud

DrZzs YouTube Video Review - MSR-1

MSR-1 MSR-1 Reviews

Apollo MSR-1 review starts at 19:53.

Updated 1 week ago by justin@apolloautomation.cloud

Smart Home Scene Review - MSR-1

MSR-1 MSR-1 Reviews

Smart Home Scene MSR-1 Review

Updated 1 week ago by justin@apolloautomation.cloud

Smart Home Scene Review - AIR-1

AIR-1 AIR-1 Reviews

Smart Home Scene AIR-1 Review

Updated 1 week ago by justin@apolloautomation.cloud

The Bearded Tech Guy YouTube Video Review - AIR-1

AIR-1 AIR-1 Reviews

Updated 1 week ago by justin@apolloautomation.cloud

How To Tune mmWave Using HLKRadarTool

MSR-1 Calibrating And Updating

Auto-Calibration (Average, Maximum, and Intelligent)1. Download the HLKRadarTool app for either A...

Updated 2 weeks ago by justin@apolloautomation.cloud

Reducing LD2410 Log Entries In Home Assistant

MSR-1 Additional Info

Open your Home Assistant config.yaml Add in this code but use your MSR-1's name logbook: ...

Updated 2 weeks ago by Trevor

CO2 Calibration For MSR-1

MSR-1 Calibrating And Updating

Please refer to the General CO2 Calibration article

Updated 2 weeks ago by justin@apolloautomation.cloud